Nickel aluminium bronze
C63000
Wrought copper-aluminium-nickel alloy considered for marine hardware, loaded bushes and wear parts.
Specify wrought product form and condition. Do not substitute a cast bronze designation.

Chemistry, properties & fasteners
Aluminium bronze and related copper alloys, led by C63000 nickel-aluminium bronze — supplied as flanges, studs, nuts and parts to drawing for marine and fire-safety systems.
Request a QuoteGrade · condition · drawing · traceability
EMG / MATERIAL DOSSIER
C63000 nickel-aluminium bronze combines about 10% aluminium, 5% nickel and 4% iron in a copper base. It offers high strength for a copper alloy with good seawater performance.
ASTM B150 covers aluminium bronze rod, bar and shapes, and ASTM B124 covers forgings. Other copper alloys are quoted to the alloy and standard named on the drawing.
STRENGTH / CONDITION / PRODUCT FORM
| Section size | Tensile min (ksi) | Yield 0.5% min (ksi) | Elongation min (%) |
|---|---|---|---|
| Up to 1 in | 110 | 68 | 10 |
| Over 1 to 2 in | 106 | 60 | 10 |
| Over 2 to 3 in | 100 | 50 | 10 |
Values per ASTM B150; limits vary by temper and section, for orientation. The edition named on your purchase order governs acceptance.
HEAT CHEMISTRY / COMPOSITION LIMITS
Nominal composition (range midpoints, orientation only)
| Element | Symbol | Min % | Max % |
|---|---|---|---|
| Copper | Cu | 78.0 | — |
| Aluminium | Al | 9.0 | 11.0 |
| Nickel + Cobalt | Ni+Co | 4.0 | 5.5 |
| Iron | Fe | 2.0 | 4.0 |
| Manganese | Mn | — | 1.5 |
| Silicon | Si | — | 0.25 |
| Tin | Sn | — | 0.20 |
| Zinc | Zn | — | 0.30 |
Values per ASTM B150 for C63000, for orientation. The edition named on your purchase order governs acceptance.
PURCHASE ORDER / ACCEPTANCE RECORDS
Aluminium bronze rod, bar and shapes, including C63000.
Copper and copper-alloy forging rod, bar and shapes.
Nonferrous bolts, studs and nuts where the drawing names a listed copper alloy.
Inspection document type, PMI and witness scope stated on the RFQ.
SPECIALISED INDUSTRIAL PROCUREMENT
EMG reviews Copper & Bronze Alloys bolts, studs, companion nuts, washers and drawing-controlled components for industrial projects. Specify the exact alloy, condition and assembly requirements. Supply is buy-to-order with quoted lead time, not a stock catalogue or general hardware service.
A blind flange, stud bolts and nuts in C63000 nickel aluminium bronze, supplied with the client's specified gasket. Built around the client's drawings and specifications, the package was supplied on time and air-freighted to the client for offshore use.
The client came to EMG through a colleague's referral after being unable to source the required parts from other Australian suppliers, and reported being very happy with the quality.
Read the Case Study


Project-specific supply outcome; not a stock or guaranteed lead-time offer. C63000 applies to the metal parts shown, not the gasket. Future requirements are buy-to-order, with quoted lead time and specification review.
Copper alloys are not one interchangeable material. Nickel aluminium bronze, silicon bronze and phosphor bronze have different compositions, strengths and wear characteristics. Selecting a family name alone is not enough for a critical purchase order.
EMG reviews bronze fastener and machined-component requirements through qualified supply partners. Send the UNS designation, drawing revision, quantity and operating environment so the proposed material route can be checked against your specification.
Explore the materials reference
C63000
Wrought copper-aluminium-nickel alloy considered for marine hardware, loaded bushes and wear parts.
Specify wrought product form and condition. Do not substitute a cast bronze designation.
C65500
Wrought high-silicon bronze considered for corrosion-resistant hardware and selected fasteners.
Confirm required strength, thread form and compatibility with the mating assembly.
C51000
Copper-tin-phosphorus alloy considered for bearing, spring and electrical-contact applications.
Temper, product form and bearing design govern suitability; it is not a universal replacement for C63000.
Reference designations are not stock, certified equivalence or guaranteed service suitability. Final product requirements govern every quotation.

Specified corrosion-resistant hardware, bushes and sleeves for marine equipment, subject to design approval.

Drawing-based bearing bushes, wear rings and sleeves with fits, surface finish and lubrication requirements defined.

Replacement wear components and specialised hardware where the OEM specifies a copper alloy.
A cast valve-body alloy and a wrought shaft or bolt alloy can have different designations and properties. State the exact product specification, not simply ‘bronze’.
Consider galvanic compatibility, seawater exposure, lubrication, shaft finish and contact pressure when selecting bushes or sleeves.
Copper-alloy selection does not make a component automatically non-sparking, non-magnetic or approved for a hazardous area. Those requirements need separate verification.
EMG accepts drawing-led enquiries for bronze bolts, nuts, bushes, sleeves and wear parts. Alloy, product form, partner capability, certification and lead time are confirmed at quotation; this is not a stock listing.
No. C63000 is a nickel aluminium bronze; C65500 is a high-silicon bronze. Their compositions and properties differ. Any substitution needs the responsible engineer’s approval.
Include the UNS designation, product specification and condition, drawing revision, quantity, fits, finish, service environment, inspection requirements and delivery date.
Not by family name alone. Define the exact alloy, wrought or cast product form, condition and required properties; substitution requires the responsible engineer’s approval.
For Copper & Bronze Alloys fasteners or machined components, send your drawing, quantity, material condition and required delivery date. EMG confirms sourcing, partner capacity, inspection records and lead time against your RFQ.
Revision, thread form, fits and surface finish.
UNS, product standard, heat treatment and service requirements.
Specify EN 10204 3.1 / 3.2, PMI and witness requirements where applicable.
Managed supply through qualified partners; no claim of EMG-owned machinery or guaranteed stock.
Producer references support alloy identification; the approved drawing and governing specification control acceptance. INCONEL and NITRONIC are trademarks of their respective owners. No authorised affiliation is implied.
Our technical team is available 24/7 to assist with material selection, specifications, and urgent requirements.
24/7 availability for critical projects