Quotes typically within 24 hours
    Precision-machined shafts, housings and threaded components illustrating component applications
    Nickel-copper alloy

    Monel 400 (UNS N04400)

    Chemistry, properties & fasteners

    A nickel-copper alloy specified for seawater and selected chemical service — supplied as bolts, studs, nuts and parts to drawing where the materials schedule calls for alloy 400.

    Request a Quote
    UNS N04400

    Grade · condition · drawing · traceability

    ENGINEERED SUPPLY, NOT OFF-THE-SHELFQUALIFIED PARTNER NETWORKLEAD TIME CONFIRMED PER RFQ

    EMG / MATERIAL DOSSIER

    The specification behind the part.

    UNS
    N04400
    Tensile, B164 annealed
    70 ksi min
    Yield, B164 annealed
    25 ksi min
    F468 fastener tensile
    80–130 ksi
    Strengthening
    Cold work
    Magnetic
    Slightly

    Alloy identity. Product requirements.

    Monel 400 (UNS N04400) is roughly two-thirds nickel and one-third copper. It is strengthened by cold work only, so strength depends on the supplied condition and section size.

    ASTM B164 covers nickel-copper rod and bar; ASTM F468 and F467 list alloy 400 bolts, studs and nuts. Name both the bar and fastener standards on the order.

    STRENGTH / CONDITION / PRODUCT FORM

    Mechanical properties

    Rod & bar — ASTM B164

    Rod & bar — ASTM B164
    ConditionTensile min (ksi)Yield 0.2% min (ksi)Elongation min (%)
    Annealed702535
    Hot worked753025

    Values per ASTM B164, for orientation. The edition named on your purchase order governs acceptance.

    Bolts & studs — ASTM F468 Ni 400

    Bolts & studs — ASTM F468 Ni 400
    SizeFull-size tensile (ksi)Yield min (ksi)
    All sizes80–13040

    Values per ASTM F468, for orientation. The edition named on your purchase order governs acceptance.

    HEAT CHEMISTRY / COMPOSITION LIMITS

    Chemical composition

    Nominal composition (range midpoints, orientation only)

    • Ni ≈ 66%
    • Cu ≈ 31.5%
    • Fe ≈ 1.2%
    • Mn ≈ 1%
    • Other ≈ 0.3%
    Monel 400 chemical composition limits
    ElementSymbolMin %Max %
    Nickel + CobaltNi+Co63.0—
    CopperCu28.034.0
    IronFe—2.5
    ManganeseMn—2.0
    SiliconSi—0.5
    CarbonC—0.3
    SulfurS—0.024

    Values per ASTM B164, for orientation. The edition named on your purchase order governs acceptance.

    PURCHASE ORDER / ACCEPTANCE RECORDS

    Standards & documentation

    ASTM B164

    Nickel-copper rod, bar and wire — raw material for 400 fasteners.

    ASTM F468 / F467

    Nonferrous bolts, studs and nuts, including Ni 400.

    ASME SB-164

    ASME Section II adoption of B164.

    EN 10204 3.1 / 3.2

    Inspection document type, PMI and witness scope stated on the RFQ.

    SPECIALISED INDUSTRIAL PROCUREMENT

    Monel 400 fasteners. A complete requirement.

    EMG reviews Monel 400 bolts, studs, companion nuts, washers and drawing-controlled components for industrial projects. Specify the exact alloy, condition and assembly requirements. Supply is buy-to-order with quoted lead time, not a stock catalogue or general hardware service.

    MATERIAL / APPLICATION / CONDITION

    Monel 400: define product form and condition

    Monel 400 is a nickel-copper alloy used in selected marine and chemical equipment. Strength depends on the product form and supplied condition rather than a precipitation-hardening treatment like K-500.

    EMG reviews Monel 400 requirements through qualified supply partners. Include the drawing revision, quantity, material condition and required site date so sourcing and documentation can be defined before an order is placed.

    Explore the materials reference
    304H stainless heavy hex nuts in project packaging; reference fastener imagery
    EMG component imagery. Photographs illustrate component types; the material certificate verifies the supplied grade.
    PROCUREMENT REFERENCE

    What to specify

    Monel 400

    UNS N04400

    Marine hardware · chemical-service components

    RFQ CHECK

    Confirm product standard, annealed or cold-worked condition, required strength and compatibility with the actual fluid chemistry.

    Reference designations are not stock, certified equivalence or guaranteed service suitability. Final product requirements govern every quotation.

    WHERE THE SPECIFICATION MATTERS

    Engineered around the application

    Water treatment plant and industrial water-handling equipment

    Marine and fluid-handling equipment

    Specified threaded hardware, pump parts and valve components in systems whose approved materials schedule calls for nickel-copper alloy 400.

    Socket head cap screws illustrating threaded-component applications

    Fastener assemblies

    Studs, hex bolts and companion nuts in Monel 400 to the approved drawing. Confirm thread form, length, mating material and any coating requirements.

    Duplex machined valve body illustrating valve-component geometry, not the featured alloy

    Parts to drawing

    Shafts, sleeves, collars and valve parts supplied through qualified manufacturing partners. Fits, surface finish, treatment and usable capacity are confirmed per enquiry.

    ENGINEERING CHECKPOINTS

    Control the details that matter.

    01

    The product specification governs

    Confirm product standard, annealed or cold-worked condition, required strength and compatibility with the actual fluid chemistry.

    02

    No automatic substitutions

    Monel 400 and Monel K-500 are different UNS alloys. A demand for higher strength does not authorise a substitution without engineering review.

    03

    Verify the finished part

    State the required chemical, mechanical, hardness and dimensional records. Request EN 10204 3.1 / 3.2, PMI or witness inspection where the project requires them; the quotation must identify the agreed scope.

    MATERIAL QUESTIONS

    Ordering Monel 400

    What is Monel 400?

    Monel 400 is a nickel-copper alloy used in selected marine and chemical equipment. Strength depends on the product form and supplied condition rather than a precipitation-hardening treatment like K-500.

    What should a Monel 400 RFQ include?

    Confirm product standard, annealed or cold-worked condition, required strength and compatibility with the actual fluid chemistry. Include dimensions or drawing revision, quantity, inspection scope and the required site date.

    Can EMG supply Monel 400 bolts and machined parts?

    EMG accepts specification-led enquiries for industrial fasteners and components. Product form, sourcing, partner capacity, certification and lead time are confirmed at quotation; this page does not establish stock or guaranteed service suitability.

    Can I substitute a related alloy?

    Monel 400 and Monel K-500 are different UNS alloys. A demand for higher strength does not authorise a substitution without engineering review.

    Should a Monel 400 nut match a K-500 stud automatically?

    No automatic pairing applies. Define the companion nut alloy, condition and assembly requirements on the drawing; Monel 400 and K-500 have different alloy identities and strength-development routes.

    YOUR SPECIFICATION. OUR SUPPLY NETWORK.

    Send the requirement.
    Get a defined supply route.

    For Monel 400 fasteners or machined components, send your drawing, quantity, material condition and required delivery date. EMG confirms sourcing, partner capacity, inspection records and lead time against your RFQ.

    Drawing & dimensions

    Revision, thread form, fits and surface finish.

    Material & condition

    UNS, product standard, heat treatment and service requirements.

    Inspection & records

    Specify EN 10204 3.1 / 3.2, PMI and witness requirements where applicable.

    Managed supply through qualified partners; no claim of EMG-owned machinery or guaranteed stock.

    Quotes typically within 24 hours.

    Connected capabilities

    TECHNICAL REFERENCES

    Monel 400 — producer material reference

    Producer references support alloy identification; the approved drawing and governing specification control acceptance. INCONEL and NITRONIC are trademarks of their respective owners. No authorised affiliation is implied.

    GET IN TOUCH

    Ready to Source Your Next Project?

    Our technical team is available 24/7 to assist with material selection, specifications, and urgent requirements.

    INDUSTRIAL PROJECT ENQUIRY

    Request a Quote

    PDF, XLSX, CSV, CAD or images · up to 10 files, 25 MB each

    Quotes typically within 24 hours. Specialised industrial supply, buy-to-order with quoted lead time.

    Emergency Support

    24/7 availability for critical projects