Monel K-500
UNS N05500
Loaded marine parts · shafts · special bolting
Specify heat-treatment condition, mechanical and hardness requirements, and any restrictions relevant to the operating environment.

Chemistry, properties & fasteners
An age-hardenable nickel-copper alloy with aluminium and titanium — supplied as high-strength bolts, studs, shafts and parts to drawing for marine and pump assemblies.
Request a QuoteGrade · condition · drawing · traceability
EMG / MATERIAL DOSSIER
Monel K-500 (UNS N05500) keeps the nickel-copper base of alloy 400 but adds aluminium and titanium, so controlled ageing can roughly double its yield strength.
ASTM B865 covers K-500 rod, bar and forgings by condition; ASTM F468 / F467 list K-500 bolts, studs and nuts. Certificates for Monel 400 do not prove K-500 acceptance.
STRENGTH / CONDITION / PRODUCT FORM
| Condition | Tensile min (ksi) | Yield 0.2% min (ksi) | Elongation min (%) |
|---|---|---|---|
| Hot finished + aged | 140 | 100 | 17 |
| Annealed + aged | 130 | 85 | 20 |
Values per ASTM B865, for orientation. The edition named on your purchase order governs acceptance.
| Size | Full-size tensile min (ksi) | Yield min (ksi) |
|---|---|---|
| All sizes | 130 | 90 |
Values per ASTM F468, for orientation. The edition named on your purchase order governs acceptance.
HEAT CHEMISTRY / COMPOSITION LIMITS
Nominal composition (range midpoints, orientation only)
| Element | Symbol | Min % | Max % |
|---|---|---|---|
| Nickel + Cobalt | Ni+Co | 63.0 | 70.0 |
| Copper | Cu | Balance | — |
| Aluminium | Al | 2.30 | 3.15 |
| Titanium | Ti | 0.35 | 0.85 |
| Iron | Fe | — | 2.0 |
| Manganese | Mn | — | 1.5 |
| Silicon | Si | — | 0.5 |
| Carbon | C | — | 0.25 |
| Sulfur | S | — | 0.01 |
Values per ASTM B865, for orientation. The edition named on your purchase order governs acceptance.
PURCHASE ORDER / ACCEPTANCE RECORDS
Precipitation-hardened Ni-Cu-Al rod, bar and forgings.
Nonferrous bolts, studs and nuts, including Ni 500.
Sour-service hardness and condition limits apply to the finished part.
Inspection document type, PMI and witness scope stated on the RFQ.
SPECIALISED INDUSTRIAL PROCUREMENT
EMG reviews Monel K-500 bolts, studs, companion nuts, washers and drawing-controlled components for industrial projects. Specify the exact alloy, condition and assembly requirements. Supply is buy-to-order with quoted lead time, not a stock catalogue or general hardware service.
K-500 adds aluminium and titanium to a nickel-copper alloy system so controlled ageing can develop strength. The treatment and finished-part acceptance criteria distinguish it from Monel 400.
EMG reviews Monel K-500 requirements through qualified supply partners. Include the drawing revision, quantity, material condition and required site date so sourcing and documentation can be defined before an order is placed.
Explore the materials reference
UNS N05500
Loaded marine parts · shafts · special bolting
Specify heat-treatment condition, mechanical and hardness requirements, and any restrictions relevant to the operating environment.
Reference designations are not stock, certified equivalence or guaranteed service suitability. Final product requirements govern every quotation.

Specified shafts, bolts, studs and valve parts requiring the drawing-defined strength and corrosion behaviour of K-500.

Studs, hex bolts and companion nuts in Monel K-500 to the approved drawing. Confirm thread form, length, mating material and any coating requirements.

Shafts, sleeves, collars and valve parts supplied through qualified manufacturing partners. Fits, surface finish, treatment and usable capacity are confirmed per enquiry.
Specify heat-treatment condition, mechanical and hardness requirements, and any restrictions relevant to the operating environment.
Do not use Monel 400 certificates as evidence of K-500 acceptance. Composition and treatment must be traceable to the supplied component.
State the required chemical, mechanical, hardness and dimensional records. Request EN 10204 3.1 / 3.2, PMI or witness inspection where the project requires them; the quotation must identify the agreed scope.
K-500 adds aluminium and titanium to a nickel-copper alloy system so controlled ageing can develop strength. The treatment and finished-part acceptance criteria distinguish it from Monel 400.
Specify heat-treatment condition, mechanical and hardness requirements, and any restrictions relevant to the operating environment. Include dimensions or drawing revision, quantity, inspection scope and the required site date.
EMG accepts specification-led enquiries for industrial fasteners and components. Product form, sourcing, partner capacity, certification and lead time are confirmed at quotation; this page does not establish stock or guaranteed service suitability.
Do not use Monel 400 certificates as evidence of K-500 acceptance. Composition and treatment must be traceable to the supplied component.
Identify UNS N05500, the specified product form and final treatment, mechanical and hardness acceptance, heat traceability and dimensional inspection. Monel 400 records cannot establish K-500 acceptance.
For Monel K-500 fasteners or machined components, send your drawing, quantity, material condition and required delivery date. EMG confirms sourcing, partner capacity, inspection records and lead time against your RFQ.
Revision, thread form, fits and surface finish.
UNS, product standard, heat treatment and service requirements.
Specify EN 10204 3.1 / 3.2, PMI and witness requirements where applicable.
Managed supply through qualified partners; no claim of EMG-owned machinery or guaranteed stock.
Producer references support alloy identification; the approved drawing and governing specification control acceptance. INCONEL and NITRONIC are trademarks of their respective owners. No authorised affiliation is implied.
Our technical team is available 24/7 to assist with material selection, specifications, and urgent requirements.
24/7 availability for critical projects