Quotes typically within 24 hours
    Duplex machined valve body illustrating valve-component geometry, not the featured alloy
    Precipitation-hardening stainless

    17-4 PH Stainless Steel (UNS S17400)

    Chemistry, properties & fasteners

    A martensitic precipitation-hardening stainless steel — supplied as shafts, bolts, pins and machined parts to drawing in the specified ageing condition.

    Request a Quote
    UNS S17400

    Grade · condition · drawing · traceability

    ENGINEERED SUPPLY, NOT OFF-THE-SHELFQUALIFIED PARTNER NETWORKLEAD TIME CONFIRMED PER RFQ

    EMG / MATERIAL DOSSIER

    The specification behind the part.

    UNS
    S17400
    Tensile, H1025
    155 ksi min
    Yield, H1025
    145 ksi min
    Hardness, H1025
    35 HRC min
    Strengthening
    Precipitation
    Magnetic
    Yes

    Alloy identity. Product requirements.

    17-4 PH (UNS S17400, Type 630) contains about 17% chromium, 4% nickel and 4% copper. Ageing at a chosen temperature after solution treatment sets the strength, named by condition such as H900, H1025 or H1150.

    ASTM A564 covers Type 630 bar and shapes. The condition designation must be on the order — strength and hardness change significantly between conditions.

    STRENGTH / CONDITION / PRODUCT FORM

    Mechanical properties

    Bar — ASTM A564 Type 630

    Bar — ASTM A564 Type 630
    ConditionTensile min (ksi)Yield 0.2% min (ksi)Elongation min (%)Hardness min
    H9001901701040 HRC
    H10251551451235 HRC
    H10751451251331 HRC
    H11501351051628 HRC

    Values per ASTM A564, for orientation. The edition named on your purchase order governs acceptance.

    HEAT CHEMISTRY / COMPOSITION LIMITS

    Chemical composition

    Nominal composition (range midpoints, orientation only)

    • Fe ≈ 73.5%
    • Cr ≈ 16.25%
    • Ni ≈ 4%
    • Cu ≈ 4%
    • Other ≈ 2.25%
    17-4 PH Stainless Steel chemical composition limits
    ElementSymbolMin %Max %
    ChromiumCr15.017.5
    NickelNi3.05.0
    CopperCu3.05.0
    Niobium + TantalumNb+Ta0.150.45
    ManganeseMn—1.00
    SiliconSi—1.00
    CarbonC—0.07
    PhosphorusP—0.040
    SulfurS—0.030
    IronFeBalance—

    Values per ASTM A564 Type 630, for orientation. The edition named on your purchase order governs acceptance.

    PURCHASE ORDER / ACCEPTANCE RECORDS

    Standards & documentation

    ASTM A564

    Precipitation-hardening stainless bar and shapes, Type 630.

    ASTM A693 / A705

    Plate and forging forms of Type 630.

    NACE MR0175 / ISO 15156

    Sour-service use is limited to specific conditions and hardness — verify against the actual part.

    EN 10204 3.1 / 3.2

    Inspection document type, PMI and witness scope stated on the RFQ.

    SPECIALISED INDUSTRIAL PROCUREMENT

    17-4 PH Stainless Steel fasteners. A complete requirement.

    EMG reviews 17-4 PH Stainless Steel bolts, studs, companion nuts, washers and drawing-controlled components for industrial projects. Specify the exact alloy, condition and assembly requirements. Supply is buy-to-order with quoted lead time, not a stock catalogue or general hardware service.

    MATERIAL / APPLICATION / CONDITION

    17-4 PH: condition is part of the specification

    17-4 PH (UNS S17400) is a chromium-nickel-copper precipitation-hardening stainless steel. It combines corrosion resistance with strength developed through heat treatment and is used for selected shafts, valve parts and engineered fasteners.

    The condition is a procurement-critical detail. H900, H1025, H1150 and other specified conditions are not interchangeable: strength, hardness and toughness change with the treatment. EMG reviews the drawing and required condition before proposing supply through qualified partners.

    Explore the materials reference
    B7M collar bolt and matching nuts illustrating custom fastener geometry, not the featured alloy
    EMG component imagery. Photographs illustrate component types; the material certificate verifies the supplied grade.
    PROCUREMENT REFERENCE

    What to specify

    17-4 PH / Type 630

    S17400

    Precipitation-hardening stainless for specified load-bearing fasteners, shafts and valve components.

    RFQ CHECK

    State the final heat-treatment condition, product standard and required mechanical properties.

    Condition-specific supply

    H900 / H1025 / H1150

    Examples of commonly specified ageing conditions; the drawing must identify the required route.

    RFQ CHECK

    These are treatment designations, not different UNS alloys or a promise of availability.

    Reference designations are not stock, certified equivalence or guaranteed service suitability. Final product requirements govern every quotation.

    WHERE THE SPECIFICATION MATTERS

    Engineered around the application

    Precision-machined shafts, housings and threaded components illustrating component applications

    Valve & actuator components

    Stems, shafts and loaded parts where the approved design calls for condition-controlled precipitation-hardening stainless.

    Mining and minerals processing plant

    Pumps & mining equipment

    Shafts, sleeves and mechanical parts with defined strength, fit and corrosion requirements.

    304H stainless heavy hex nuts in project packaging; reference fastener imagery

    Special fasteners

    Bolts, studs and nuts to drawing with a specified final condition and matching assembly requirements.

    ENGINEERING CHECKPOINTS

    Control the details that matter.

    01

    Condition before strength

    Do not apply a single tensile or hardness value to every 17-4 PH part. The governing specification, section size and heat-treatment condition determine acceptance.

    02

    Sour service is conditional

    A 17-4 PH designation alone does not establish NACE MR0175 / ISO 15156 suitability. Check the permitted treatment, hardness and environmental restrictions with the responsible engineer.

    03

    Inspect the finished component

    Specify heat-treatment records, mechanical tests, hardness, dimensional inspection and any additional non-destructive examination required by the drawing.

    MATERIAL QUESTIONS

    Ordering 17-4 PH Stainless Steel

    Is 17-4 PH the same as 316 stainless steel?

    No. 17-4 PH is a precipitation-hardening stainless; 316 is an austenitic stainless. They differ in structure, strength development and corrosion behaviour. Neither is an automatic substitute for the other.

    Can I order 17-4 PH without a heat-treatment condition?

    For a critical component, specify the condition required by the drawing or engineering specification. If it is missing, EMG will seek clarification rather than choose a condition on your behalf.

    Can EMG quote 17-4 PH bolts and machined components?

    Yes, submit the drawing, final condition, quantity, inspection scope and site date. Material route, partner capacity, records and lead time are confirmed per RFQ.

    Can H900 be supplied instead of H1150 without approval?

    No. These are different heat-treatment conditions with different properties. Use the condition required by the approved drawing and obtain engineering approval for any change.

    YOUR SPECIFICATION. OUR SUPPLY NETWORK.

    Send the requirement.
    Get a defined supply route.

    For 17-4 PH Stainless Steel fasteners or machined components, send your drawing, quantity, material condition and required delivery date. EMG confirms sourcing, partner capacity, inspection records and lead time against your RFQ.

    Drawing & dimensions

    Revision, thread form, fits and surface finish.

    Material & condition

    UNS, product standard, heat treatment and service requirements.

    Inspection & records

    Specify EN 10204 3.1 / 3.2, PMI and witness requirements where applicable.

    Managed supply through qualified partners; no claim of EMG-owned machinery or guaranteed stock.

    Quotes typically within 24 hours.

    Connected capabilities

    TECHNICAL REFERENCES

    ATI — 17-4 precipitation-hardening stainless

    Producer references support alloy identification; the approved drawing and governing specification control acceptance. INCONEL and NITRONIC are trademarks of their respective owners. No authorised affiliation is implied.

    GET IN TOUCH

    Ready to Source Your Next Project?

    Our technical team is available 24/7 to assist with material selection, specifications, and urgent requirements.

    INDUSTRIAL PROJECT ENQUIRY

    Request a Quote

    PDF, XLSX, CSV, CAD or images · up to 10 files, 25 MB each

    Quotes typically within 24 hours. Specialised industrial supply, buy-to-order with quoted lead time.

    Emergency Support

    24/7 availability for critical projects