Hastelloy C-276
UNS N10276
Chemical process bolting · corrosion-exposed parts
Define fluid composition, concentration, contaminants, product form and condition. Corrosion selection belongs to the responsible engineer.

Chemistry, properties & fasteners
A low-carbon nickel-molybdenum-chromium-tungsten alloy specified for oxidising and reducing chemical-process environments — supplied as studs, bolts, nuts and parts to drawing.
Request a QuoteGrade · condition · drawing · traceability
EMG / MATERIAL DOSSIER
Hastelloy C-276 (UNS N10276) carries roughly 16% molybdenum, 15.5% chromium and 3.75% tungsten in a nickel base. Very low carbon and silicon limit grain-boundary precipitation in welded and heat-affected zones.
ASTM B574 covers C-276 rod and bar; ASTM F468 lists C-276 externally threaded fasteners as Ni 276, with companion nuts to ASTM F467. Material certification for bar does not by itself establish finished-fastener conformity — name both on the purchase order.
STRENGTH / CONDITION / PRODUCT FORM
| Condition | Tensile min (ksi) | Yield 0.2% min (ksi) | Elongation min (%) |
|---|---|---|---|
| Solution annealed, all sizes | 100 | 41 | 40 |
Values per ASTM B574, for orientation. The edition named on your purchase order governs acceptance.
| Size | Hardness | Full-size tensile (ksi) | Yield min (ksi) | Elongation min (%) |
|---|---|---|---|---|
| All sizes | 20–32 HRC | 110–140 | 45 | 25 |
Values per ASTM F468, for orientation. The edition named on your purchase order governs acceptance.
| Nut style | Hardness min | Proof stress min (ksi) |
|---|---|---|
| Hex | 20 HRC | 110 |
| Heavy hex | 20 HRC | 119 |
Values per ASTM F467, for orientation. The edition named on your purchase order governs acceptance.
HEAT CHEMISTRY / COMPOSITION LIMITS
Nominal composition (range midpoints, orientation only)
| Element | Symbol | Min % | Max % |
|---|---|---|---|
| Nickel | Ni | Balance | — |
| Molybdenum | Mo | 15.0 | 17.0 |
| Chromium | Cr | 14.5 | 16.5 |
| Iron | Fe | 4.0 | 7.0 |
| Tungsten | W | 3.0 | 4.5 |
| Cobalt | Co | — | 2.5 |
| Manganese | Mn | — | 1.0 |
| Vanadium | V | — | 0.35 |
| Carbon | C | — | 0.010 |
| Silicon | Si | — | 0.08 |
| Phosphorus | P | — | 0.04 |
| Sulfur | S | — | 0.03 |
Values per ASTM B574 Table 1, for orientation. The edition named on your purchase order governs acceptance.
PURCHASE ORDER / ACCEPTANCE RECORDS
Low-carbon Ni-Mo-Cr rod and bar — the raw-material reference for machined C-276 fasteners.
Nonferrous bolts, hex cap screws and studs; C-276 listed as Ni 276.
Nonferrous nuts, including Ni 276 hex and heavy hex.
ASME Section II adoption of B574 for pressure-equipment material schedules.
Sour-service qualification is assessed against the actual environment and condition — alloy name alone is not compliance.
Inspection document type, PMI and witness scope stated on the RFQ.
SPECIALISED INDUSTRIAL PROCUREMENT
EMG reviews Hastelloy C-276 bolts, studs, companion nuts, washers and drawing-controlled components for industrial projects. Specify the exact alloy, condition and assembly requirements. Supply is buy-to-order with quoted lead time, not a stock catalogue or general hardware service.
C-276 is a nickel-molybdenum-chromium alloy considered for demanding chemical-process environments. It is not universally resistant to every acid, concentration or mixed process stream.
EMG reviews Hastelloy C-276 requirements through qualified supply partners. Include the drawing revision, quantity, material condition and required site date so sourcing and documentation can be defined before an order is placed.
Explore the materials reference
UNS N10276
Chemical process bolting · corrosion-exposed parts
Define fluid composition, concentration, contaminants, product form and condition. Corrosion selection belongs to the responsible engineer.
Reference designations are not stock, certified equivalence or guaranteed service suitability. Final product requirements govern every quotation.

Specified bolts, nuts, valve components and sleeves where a plant material schedule calls for C-276.

Studs, hex bolts and companion nuts in Hastelloy C-276 to the approved drawing. Confirm thread form, length, mating material and any coating requirements.

Shafts, sleeves, collars and valve parts supplied through qualified manufacturing partners. Fits, surface finish, treatment and usable capacity are confirmed per enquiry.
Define fluid composition, concentration, contaminants, product form and condition. Corrosion selection belongs to the responsible engineer.
C-276 is not C-22 or Alloy 20. A generic Hastelloy description is insufficient for procurement and does not permit substitution.
State the required chemical, mechanical, hardness and dimensional records. Request EN 10204 3.1 / 3.2, PMI or witness inspection where the project requires them; the quotation must identify the agreed scope.
C-276 is a nickel-molybdenum-chromium alloy considered for demanding chemical-process environments. It is not universally resistant to every acid, concentration or mixed process stream.
Define fluid composition, concentration, contaminants, product form and condition. Corrosion selection belongs to the responsible engineer. Include dimensions or drawing revision, quantity, inspection scope and the required site date.
EMG accepts specification-led enquiries for industrial fasteners and components. Product form, sourcing, partner capacity, certification and lead time are confirmed at quotation; this page does not establish stock or guaranteed service suitability.
C-276 is not C-22 or Alloy 20. A generic Hastelloy description is insufficient for procurement and does not permit substitution.
No. Specify C-276 / UNS N10276, the governing product specification, condition and mating assembly requirements. C-22 and other Hastelloy alloys are not interchangeable with C-276 by name.
For Hastelloy C-276 fasteners or machined components, send your drawing, quantity, material condition and required delivery date. EMG confirms sourcing, partner capacity, inspection records and lead time against your RFQ.
Revision, thread form, fits and surface finish.
UNS, product standard, heat treatment and service requirements.
Specify EN 10204 3.1 / 3.2, PMI and witness requirements where applicable.
Managed supply through qualified partners; no claim of EMG-owned machinery or guaranteed stock.
Producer references support alloy identification; the approved drawing and governing specification control acceptance. INCONEL and NITRONIC are trademarks of their respective owners. No authorised affiliation is implied.
Our technical team is available 24/7 to assist with material selection, specifications, and urgent requirements.
24/7 availability for critical projects