Quotes typically within 24 hours
    Back to Products

    Hex Head Bolts for Industrial Equipment & Plant

    Standard-pattern hex head bolts with a plain bearing face, supplied to ASME, ISO and Australian standards in the grade your specification calls for.

    EMG / BOLT DOSSIER

    Hex head bolt specifications & dimensions

    A hex head bolt has a six-sided head with a plain bearing face and is tightened with a nut. It is the standard (finished) head pattern — smaller across the flats than a heavy hex head on the same thread — and suits equipment frames, supports, machinery and general plant connections where the specification does not call for the heavy series.

    Fig. 1 · Hex head boltASME B18.2.1
    HGELTFRSIDE VIEWEND VIEW
    Schematic, not to scale. Letters match the ASME B18.2.1 dimension table below.
    Head pattern
    Standard hex, ASME B18.2.1
    Imperial range
    1/4" – 6"
    Metric range
    M5 – M150
    Threads
    UNC · UNF · 8UN · ISO metric
    Certification
    EN 10204 3.1 · 3.2 on request
    Supply
    Buy-to-order, quoted lead time
    01 · DIMENSIONS

    Hex head bolt dimensions (inch) — ASME B18.2.1

    E = body diameter · F = width across flats · G = width across corners · H = head height · R = fillet radius · LT = nominal thread length · TPI = coarse thread series.

    Hex head bolt dimensions (inch) — ASME B18.2.1
    SizeTPIE body dia.F across flatsG across cornersH head heightR filletLT thread length
    MaxMinBasicMaxMinMaxMinBasicMaxMinMaxMin≤ 6"> 6"
    1/4"200.2600.2377/160.4380.4250.5050.48411/640.1880.1500.030.010.7501.000
    5/16"180.3240.2981/20.5000.4840.5770.5527/320.2350.1950.030.010.8751.125
    3/8"160.3880.3609/160.5620.5440.6500.6201/40.2680.2260.030.011.0001.250
    7/16"140.4520.4215/80.6250.6030.7220.68719/640.3160.2720.030.011.1251.375
    1/2"130.5150.4823/40.7500.7250.8660.82611/320.3640.3020.030.011.2501.500
    5/8"110.6420.60515/160.9380.9061.0831.03327/640.4440.3780.060.021.5001.750
    3/4"100.7680.7291-1/81.1251.0881.2991.2401/20.5240.4550.060.021.7502.000
    7/8"90.8950.8521-5/161.3121.2691.5161.44737/640.6040.5310.060.022.0002.250
    1"81.0220.9761-1/21.5001.4501.7321.65343/640.7000.5910.090.032.2502.500
    1-1/8"71.1491.0981-11/161.6881.6311.9491.8593/40.7800.6580.090.032.5002.750
    1-1/4"71.2771.2231-7/81.8751.8122.1652.06627/320.8760.7490.090.032.7503.000
    1-3/8"61.4041.3452-1/162.0621.9942.3822.27329/320.9400.8100.090.033.0003.250
    1-1/2"61.5311.4702-1/42.2502.1752.5982.48011.0360.9020.090.033.2503.500
    1-5/8"8 UN1.6581.5912-7/162.4382.3562.8152.6161-3/321.1160.9780.090.033.5003.750
    1-3/4"51.7851.7162-5/82.6252.5383.0312.8931-5/321.1961.0540.120.043.7504.000
    1-7/8"8 UN1.9121.8392-13/162.8122.7193.2483.0991-1/41.2761.1300.120.044.0004.250
    2"4.52.0391.96433.0002.9003.4643.3061-11/321.3881.1750.120.044.2504.500
    2-1/4"4.52.3052.2143-3/83.3753.2623.8973.7191-1/21.5481.3270.190.064.7505.000
    2-1/2"42.5592.4613-3/43.7503.6254.3304.1331-21/321.7081.4790.190.065.2505.500
    2-3/4"42.8272.7114-1/84.1253.9884.7634.5461-13/161.8691.6320.190.065.7506.000
    3"43.0812.9614-1/24.5004.3505.1964.95922.0601.8150.190.066.2506.500
    3-1/4"43.3353.2104-7/84.8754.7125.6295.3722-3/162.2511.9360.190.066.7507.000
    3-1/2"43.5893.4615-1/45.2505.0756.0625.7862-5/162.3802.0570.190.067.2507.500
    3-3/4"43.8583.7265-5/85.6255.4376.4956.1982-1/22.5722.2410.190.067.7508.000
    4"44.1113.97566.0005.8006.9286.6122-11/162.7642.4240.190.068.2508.500

    All dimensions in inches. Sizes from 1/4" and up to 6", and metric M5 to M150 (ISO 4014/4017, EN 14399-4, AS/NZS 1252), are quoted to your drawing or specification. Reference only — your purchase order and the governing standard edition take precedence.

    02 · STANDARDS

    Governing standards

    ASME B18.2.1

    Inch hex bolt head dimensions and tolerances

    ASME B1.1

    Unified inch screw threads (UNC, UNF, 8UN)

    ISO 4014 / ISO 4017

    Metric hex head bolts, partial and full thread

    AS 1111 / AS 1110

    Australian metric commercial and precision hex bolts

    ASTM A307 / SAE J429

    General-purpose carbon and Grade 5 / 8 bolting

    ASTM A193 / A320

    Pressure and low-temperature alloy and stainless grades

    ASTM F593 / ISO 3506

    Stainless steel bolts (inch and metric A2 / A4)

    EN 10204

    3.1 inspection certificate as standard, 3.2 on request

    03 · BOLT VS SCREW

    Hex head bolts vs hex cap screws

    They look alike, but the bolt carries wider tolerances and a plain bearing face for use with a nut, while the hex cap screw has closer tolerances and a washer face for tapped holes and machined assemblies. Check which one the drawing names before ordering.

    04 · OTHER NAMES

    Also known as

    • — Hexagon head bolts
    • — Hex bolts
    • — Machine bolts
    • — Finished hex bolts
    Industrial hex head bolts with matching nuts
    Hex head bolts supplied as certified sets
    EN 10204 3.1 Certified
    ISO 9001 Quality
    Zinc yellow coated hex head bolts with rolled threads
    Coated hex head bolts with coating and mill certification
    OVERVIEW

    Overview

    EMG supplies hex head bolts for industrial plant, equipment and maintenance programmes across Australia and the Asia-Pacific. Bolts are sourced to ASME B18.2.1, ISO 4014/4017 or AS 1111 in partial or full thread, from carbon and alloy steel through stainless, duplex and nickel alloys, with matching nuts and washers and EN 10204 3.1 certification. Supply is buy-to-order with a quoted lead time.

    EMG supplies industrial hex head bolts from 1/4" to 6" and M5 to M150 to ASME B18.2.1, ISO 4014/4017 and AS 1111, with EN 10204 3.1 material certification and heat traceability.

    WHERE THEY ARE SPECIFIED

    Typical Applications

    01Equipment frames, skids and baseplates
    02Pump, motor and gearbox mounting
    03Pipe supports and cable tray structures
    04Conveyor and materials-handling plant
    05Marine and offshore secondary steelwork
    06Shutdown and maintenance replacement bolting
    SUPPLY SCOPE

    Fastener Types We Supply

    Inch hex head bolts to ASME B18.2.1
    ISO 4014 partial thread hex bolts (metric)
    ISO 4017 full thread hex bolts (metric)
    AS 1111 commercial hex bolts
    Hex head bolts in duplex and nickel alloys to drawing
    MATERIAL RANGE

    Common Materials & Grades

    ASTM A307 Gr A / BSAE J429 Gr 5 / Gr 8Property class 4.6 / 8.8 / 10.9ASTM A193 B7 / B7M / B16ASTM A320 L7304 / 316 Stainless (A2 / A4)Duplex 2205Super Duplex 2507Inconel 625 / 718Monel 400 / K-500Hastelloy C-276
    VERIFICATION

    Standards & Documentation

    EN 10204 3.1 Mill Test Reports with chemical and mechanical properties
    Heat number traceability
    Dimensional inspection to ASME B18.2.1 / ISO 4014/4017
    Hardness and proof load verification where the grade requires it
    ISO 9001:2015 certified manufacturing

    NEED MACHINED COMPONENTS TOO?

    Spacers, blinds, special nuts, shafts and bushes — supplied to your drawing with the same traceability as your bolting. Precision Machined Components →

    FREQUENTLY ASKED QUESTIONS

    Technical FAQs

    What is the difference between a hex head bolt and a heavy hex bolt?

    +
    Both follow ASME B18.2.1, but a heavy hex bolt has a larger and taller head on the same thread size — for example 7/8" across flats on a 1/2" bolt versus 3/4" for the standard hex head. Heavy hex is usually specified for pressure equipment and high-strength structural joints; standard hex suits general equipment and plant connections.

    Is a hex head bolt the same as a hex cap screw?

    +
    No. A hex head bolt has wider tolerances and a plain bearing face and is intended for use with a nut. A hex cap screw has closer tolerances and a washer face, and can be used in tapped holes. Order the one named on your drawing.

    What size range of hex head bolts can you supply?

    +
    EMG quotes hex head bolts from 1/4" to 6" in inch sizes and M5 to M150 in metric, in partial or full thread, buy-to-order with a quoted lead time.

    Do you supply matching nuts and washers?

    +
    Yes. Bolts, nuts and washers can be supplied as one set matched by grade, with certification for each component.
    GET IN TOUCH

    Need a Quote for Hex Head Bolts?

    Send us the size, grade and quantity — or your drawings and bill of materials — and we'll return a technical quote for hex head bolts with lead times and certification included.

    INDUSTRIAL PROJECT ENQUIRY

    Request a Quote

    PDF, XLSX, CSV, CAD or images · up to 10 files, 25 MB each

    Quotes typically within 24 hours. Specialised industrial supply, buy-to-order with quoted lead time.

    Emergency Support

    24/7 availability for critical projects